• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.xmyzcy.com
新闻中心当前位置:博亿彩票APP下载-新闻中心
    安装玻璃门的几点注意事项
    来源:http://www.xmyzcy.com   时间:2016-1-28 15:27:44
    安装玻璃门的几点注意事项:
    Install door several matters needing attention:
    1、安装金属饰面的木底托:先把方木固定在地面上,然后再用万能胶将金属饰面板粘在木上,方木可采用直接钉在预埋木砖上,或通过膨胀螺栓连接的方法固定。济南玻璃门
    1, install metal decorative surface wood tap: put the wood on the ground, and then use all-purpose adhesive to metal veneer glued on the wood, the wood can be used directly on the embedded wooden brick, or fixed by the method of expansion bolt connection.
    2、安装竖向门框:接所弹中心线钉立门框方木,然后用胶合板确定门框柱的外形和位置,后外包金属装饰面。
    2, install the vertical frame: connect the harp center line nail doorcase the wood, then the position and the shape of the frame column plywood, finally outsourcing metal decorative surface.
    3、安装框顶部限位槽:限位槽的宽应大于玻璃厚度2-4mm,槽深为10-20mm。安装时,先由所弹中凡线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。
    3, install box at the top of the tank: limit slot width should be greater than the thickness of the glass 2-4 mm, deeply 10-20 mm slot. When installation, first by playing in every line leads to two metal decorative edges, and then the installation of the door frame according to line the top limit slot.
    4、安装玻璃:用玻璃吸盘机把厚玻璃吸紧,然后手握吸盘把由2-3人将厚玻璃板抬起,移至安装位置。
    4, install glass: the thick glass suction with glass sucker machine, and then hand sucker by 2-3 people to raise plate glass, moved to the installation location.
    5、固定玻璃:在底托方木上的内外钉两根小方木条把厚玻璃夹在中门,方木条距玻璃板面4mm左右,然后在方木条上涂刷万能胶,将饰面金属粘卡在方木条上。
    5, fixed glass: tap the wood on the inside and outside nail article two small squares in thick glass sandwiched between the door, wood article is apart from the glass panel 4 mm or so, then the article in the wood coating adhesive, the article will finish metal sticking in the wood.
    6、注玻璃胶封口:在顶部限位槽和底部托槽口的两侧,以及厚玻璃与框柱的对缝处等各缝隙处,注入玻璃胶封口。
    6, note the glass glue sealing: at the top limit slot and the bottom of the both sides of the slot, and thickness of glass and frame columns on the side seam each aperture place, such as injection glue sealing glass.
    7、玻璃之间对接:玻璃门固定部分因尺寸过大而需要拼接玻璃时,其对缝要有2-3mm的宽度,玻璃板边要进行倒角处理。

    Docking between 7, glass, glass door fixed part need Mosaic glass, due to size is too large for the seam should have 2-3 mm width, glass edge chamfering processing.

    本文由济南玻璃门博亿彩票APP下载整理发表提供,详情请关注公司网站:http://www.xmyzcy.com/

河北快3走势图 必博彩票平台 爱购彩票APP 河北快3走势图 百万彩票APP 博亿彩票APP下载 河北快3走势图 博牛彩票APP下载 百盈彩票平台 爱淘彩票平台