• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.xmyzcy.com
新闻中心当前位置:博亿彩票APP下载-新闻中心
    玻璃门安装方法大全
    来源:http://www.xmyzcy.com   时间:2016-8-25 10:30:36
    玻璃门不是我们所陌生的东西了,当你的新房已经修葺好了,准备进行玻璃门的安装时候,有没有担心过安装师傅的差错让你漂亮的门美中不足呢?那么下面我们一起来看看玻璃门的安装方法介绍,以便于以后师傅操作起来或者我们自己有兴趣安装的话能够不走弯路错路。
      Glass door is not our strange things. When your new house has a good repair for glass door installation, do not worry about the installation of master errors you beautiful doors fly in the ointment? Then we have to look at the glass door installation method introduced in order to facilitate the future master or our own interest in the installation of the words can not take the wrong way.
      1、定位、放线:由固定玻璃和活动玻璃门扇组合在的玻璃门,统一进行放线定位。
      1, positioning, line: by the fixed glass and glass door activity combination in the glass door, unified line positioning.
      2、安装框顶部限位槽:限位槽的宽应大于玻璃厚度2-4mm,槽深为10-20mm。安装时,先由所弹中凡线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。
      2, the top limit of the installation frame slot: the width of the limit slot should be greater than the glass thickness 2-4mm, the groove depth of 10-20mm. When installed, the play where the line leads to two metal decorative plate edge and press the edge line were at the top of the door frame limit the installation of slot.
      3、安装金属饰面的木底托:先把方木固定在地面上,然后再用万能胶将金属饰面板粘在木上,方木可采用直接钉在预埋木砖上,或通过膨胀螺栓连接的方法固定。
      3, the installation of metal decorative wood base care: first the timbers are fixed on the ground and then glue will metal decorative panel bonded in the wood, the wood can be the nail in the pre buried block, or through the expansion bolt connection method of fixed.
      4、安装竖向门框:接所弹中心线钉立门框方木,然后用胶合板确定门框柱的外形和位置,后外包金属装饰面。
      4, the installation of vertical frames: the bomb line nail vertical door frame timbers, and then use plywood determine the shape and position of the frame column, finally outsourcing metal decorative surface.
      5、安装玻璃:用玻璃吸盘机把厚玻璃吸紧,然后手握吸盘把由2-3人将厚玻璃板抬起,移至安装位置。
      5, the installation of glass: glass suction cup machine to the thick glass suction, and then hold the suction cup by the 2-3 will be thick glass plate up, moved to the installation location.
      6、固定玻璃:在底托方木上的内外钉两根小方木条把厚玻璃夹在中门,方木条距玻璃板面4mm左右,然后在方木条上涂刷万能胶,将饰面金属粘卡在方木条上。
      6 and fixed glass: at the end of the supporting timbers on the inside and outside nail two small wood put thick glass folder in the door, wooden bar from the surface of the glass plate with 4mm around and on the wooden bar coating adhesive, finish metal sticking on the wooden bar.
      7、注玻璃胶封口:在顶部限位槽和底部托槽口的两侧,以及厚玻璃与框柱的对缝处等各缝隙处,注入玻璃胶封口。
      7, note glass glue sealing: each of the slots on both sides of the mouth of the slot and the bottom bracket at the top limit, and thick glass and frame column butt department, injection plastic glass sealing.
      8、玻璃之间对接:玻璃门固定部分因尺寸过大而需要拼接玻璃时,其对缝要有2-3mm的宽度,玻璃板边要进行倒角处理。
      The connection between 8 and glass: glass door fixing part due to size and mosaic glass, the seam to 2-3mm width, the edge of the glass sheet to chamfer processing.
      9、动玻璃门扇安装:门扇安装前,地面地弹簧与门框顶面的定位销应定位安装完毕,两者必须同轴线,安装时用吊垂线检查,确保地弹簧转轴与定位销的中心线在同一会直线上。
      9, glass door installation: doors before installation, ground spring door frame and the top surface positioning pin positioning should be installed, both of which must be coaxial, installation hanging vertical check and ensure the spring positioning pin shaft and the center line in one line.
      10、安装玻璃门扇上下门夹:把上下金属门夹分别装在玻璃门扇上下两端,并测量门扇高度。
      10, installation of glass door door clip: the metal door clamp are respectively arranged on the glass door on the lower ends of the, and to measure the height of the door leaf.
      公司以良好的企业信誉,完美的品质,热诚的服务,取得了良好的业绩。在国内同行业中享有较高的知名度,得到广大客户的赞许和支持。
      Company to a good corporate reputation, perfect quality, dedicated service, and achieved good results. Enjoy high reputation in the same industry in China, and get the approval and support from our customers.
爱彩彩票APP下载 宝赢彩票平台 爱彩彩票APP下载 河北快3开奖结果 宝乐彩票平台 伯乐彩票APP下载 博美彩票APP下载 河北快3走势图 博悦彩票平台 博易彩票登陆