• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.xmyzcy.com
新闻中心当前位置:博亿彩票APP下载-新闻中心
    如何正确对车库门进行安装调试工作?
    来源:http://www.xmyzcy.com   时间:2019-4-22 16:18:00
    随着经济生死水平的进步,如今我们在公路上随处可见各种车辆,同时对车库门的需求也是越来越大。那么如何正确对车库门停止装置调试工作?
    With the improvement of the level of economic life and death, we can see all kinds of vehicles on the highway nowadays. At the same time, the demand for garage doors is growing. So how to correctly debug the garage door stop device?
    1、依据门口高度,将主边板和副边板用收缩螺丝程度装置在车库门门口两边,并将零件轴承座焊牢在零件副边板上,留意零件轴承座的中心与零件大链轮的中心程度。
    1. According to the gate height, the main side plate and the auxiliary side plate are installed on both sides of the garage door with shrinkage screw, and the bearing seat of the part is welded on the auxiliary side plate of the part, paying attention to the center of the bearing seat of the part and the center of the large sprocket of the part.
    2、在石家庄车库门门口两边恰当位置装置导槽。
    2. Install guide grooves on both sides of the gate of Shijiazhuang garage.
    3、将卷门上部固定在上,启动主机使卷门进入导槽,调理上限和限位位。
    3. Fix the upper part of the rolling door on top, start the main engine to make the rolling door enter the guide slot, adjust the upper limit and limit position.

    4、计算好钢管长度及轴总长度后,将零件死心穿入圆环内焊牢,再将焊好的死心和圆环穿如零件铁管在恰当的位置焊牢,然后将零件圆环穿入死心和铁管焊牢。

    济南卷帘门产品

    4. After calculating the length of the steel pipe and the total length of the shaft, the dead center of the part is penetrated into the ring and welded firmly. Then the dead center and the ring are penetrated as the iron pipe of the part is in the proper position, and then the ring of the part is penetrated into the dead center and the iron pipe.
    5、将零件六角环穿入铁管的另一端焊牢。
    5. Put the hexagonal ring of the part through the other end of the iron pipe and weld firmly.
    6、将焊有零件六角环的铁管的一端插入零件大链轮的六角位,并将另一端穿上轴承后移到焊牢在零件副边板上的轴承座。
    6. Insert one end of the iron pipe welded with the hexagonal ring of the part into the hexagonal position of the large sprocket of the part, and put the other end on the bearing and move it to the bearing seat welded firmly on the side plate of the part.
    7、将主机装在主边板上,调试主机上的两枚M6机脚外六角螺丝,使链条松紧适合,然后将主边板上的周围M10螺母紧固。
    7. Install the main frame on the main side board, debug the two M6 external hexagonal screw on the main frame, make the chain loose and fit, and then tighten the M10 nut around the main side board.
    8、主机左装(由内向外看)时,需将离合制动器旋转180度,然后将手动按纽开关的黑白线对调,遥控线的黄白对调,主机右装时无需调整。
    8. When the main engine is left mounted (from inside to outside), it is necessary to rotate the clutch brake 180 degrees, then adjust the black and white lines of the manual button switch, and the yellow and white lines of the remote control line. There is no need to adjust the right mounting of the main engine.
    本文精彩内容由济南卷帘门整理提供!希望通过小编的介绍对大家有所帮助,我们的官网是:http://www.xmyzcy.com多谢大家的阅读观看!
    The wonderful content of this article is provided by Jinan curtain door finishing! Hope to help you through the introduction of the edition, our official website is: http://www.xmyzcy.com Thank you for reading and watching!
博亿彩票APP下载 伯爵彩票APP下载 博美彩票APP下载 必中彩票APP下载 河北快3走势图 宝马彩票APP下载 博美彩票APP下载 博悦彩票APP下载 河北快3走势图 河北快3走势图